How to Change Water Filter In Whirlpool French Door Refrigerator? - Safe and Easy Guide!

If you find that the water in your refrigerator is cloudy, it might mean that you have to replace your water filter. Your water filter might have worked so hard that it needs to be refreshed. Replacing a water filter on your refrigerator is not rocket science; you can do it on your own like a pro, so keep reading to find out the easiest ways to replace Water Filter In the Whirlpool French Door refrigerator. Remember you should replace your water filter every six months and always refer to your use and care guide!

Why you might need to replace the Water Filter: 

  1. Not dispensing water
  2. Ice maker not making ice
  3. Ice maker dispenses too little ice
  4. Leaking
  5. Noisy
  6. Touchpad does not respond

Locate the water filter

  • Locate the water filter cover in the upper right-hand corner of the refrigerator interior.
  • Filter covers will have one of two different types of releases, push or pull. The push style can be identified by the word push embossed on the tab on the cover end facing out, and the pull style will have an open invoice on the front underside of the cover.
  • For the push style filter cover, release the body by pushing in on the tab and slightly downward, so the filter cover hangs open from the back at an angle.
  • For the pull style filter cover, release the body by pulling the tab gently toward the front, so the filter cover hangs open from the back at an angle.
  • If this is a new refrigerator installation, a blue bypass cap will be inside the filter opening. Remove the blue bypass cap by turning it counterclockwise, approximately one-quarter turn, and then pull straight out.
  • Keep the bypass cap for future use if needed.

Replace used filter

  • To replace a used filter, unscrew and remove the cartridge by turning it counterclockwise until it releases and then pulls straight out.
  • Discard the used filter cartridge.
  • Remove the new filter from any packaging and pull the seal off the end of the cartridge.
  • With the threads facing toward the back, align the new filter. Push in until seated.
  • Turn the filter clockwise approximately one-quarter of a turn until the filter stops.
  • Close the filter cover by lightly lifting it from underneath and pressing upward until it snaps shut.
  • To ready your waterline for use, you will now need to purge air from the water system.
How to Change Water Filter In Whirlpool French Door Refrigerator?
Locate the water filter

Water Filter

What am I supposed to do if the water is cloudy in my Whirlpool Refrigerator?

After you’ve changed your water filter and you find that the water is cloudy, you need to flush the air out of the system. and to do that, and you need to fill three gallons of water with the time frame five seconds on, five seconds off, until you have three gallons. And by then, the water should be clear.  

Replacing your every drop water filter is simple. Replace your filter every six months to optimize contaminant reduction.

Change Every Drop Water Filter In Whirlpool French Door Refrigerator

Filter 1

Step One: Be sure you have the correct filter.

Step Two:

  1. Remove your new filter from its packaging.
  2. Lift the purple cap from the top of the filter.
  3. Be sure the black O-rings are still in place.

Step Three: Locate your filter in your refrigerator. 

For Filter One, you’ll find it either inside in the upper right-hand corner of the ceiling or in the base grille. 

Step Four: Pull open the filter cover door. As the door opens, the filter will be released and eject slightly from the housing. 

Step Five: Once the door is completely open, pull the filter straight out. 

(Note: excess water may spill from the old filter, so have a towel handy.) 

Step Five: Time to install your new Every Drop filter. Hold the filter so that the arrow at the end of the cartridge is aligned correctly. 

Step Six: Align the filter with the opening and gently push the new filter into the hole. 

Step Seven: push firmly on the filter cover door until it snaps closed. 

Step Eight: flush four gallons through your refrigerator water dispenser before drinking to remove any air and ensure Every Drop’s fast flow performance. 

****Follow these instructions for cleaner-tasting water.

Filter 2

 Step One: Make sure you have the correct filter number and colored cap for your refrigerator.

Step Two: Remove and recycle your cap

Step Three: Next, find your holder. It’ll be in the interior of your refrigerator.

Step Four: Pop out the old one has a cloth handy as there may be excess water that’s completely normal reapply the bottom cap to the new one and slide it in, 

Step Five: You’ll hear it click when it’s locked but don’t over tighten and close the cover 

Step Six: Thoroughly run your dispenser to activate the filter. You may hear a loud air pressure sound, but that’s normal. 

Step Seven: Getting six new months of clean, fresh-tasting water and ice is as easy as that

Filter 3

Step One: make sure you have the correct filter number and colored cap for your refrigerator. 

Step Two: remove then recycle your cap. 

Step Three: find your holder. It’ll be at the base of your refrigerator.

Step Four: pop out the old one (have a cloth handy as there may be excess water that’s completely normal). 

Step Five: reapply the bottom cap to the new one and slide it in. you’ll hear it click. 

Step Six: when it’s locked thoroughly, run your dispenser to activate the filter. 

***you may hear a loud air pressure sound, but that’s normal. 

 Getting six new months of clean, fresh-tasting water and ice is as easy as that.

Filter 4

Step One: Be sure you have the correct filter. If you need help deciding that Filter Four is suitable for your refrigerator, use the filter finder at everydropwater.com. 

Step Two: Remove your new filter from its packaging. Pull the seal off the end of the cartridge. 

Step Three: Locate your filter in your refrigerator. 

For Filter Four, you’ll find it inside in the upper right-hand corner of the ceiling. 

Step Four: To replace a used filter, unscrew and remove the cartridge by turning it counterclockwise until it releases and then pulls straight out. (Note: excess water may spill from the old filter, so have a towel handy.) 

Step Five: install your new Every Drop filter. 

Step Six: the filter with the opening in the refrigerator and push in until seated. 

Step Seven: Turn it clockwise until the filter stops. Shut the filter cover.

Step Eight: flush four gallons through your refrigerator water dispenser before drinking.  

Change Every Drop Water Filter In Whirlpool French Door Refrigerator
Change Every Drop Water Filter In Whirlpool French Door Refrigerator
Changing Water/Ice Filter On Whirlpool Side-By-Side Refrigerator

Changing Water/Ice Filter On Whirlpool Side-By-Side Refrigerator

After replacing the filter, you will need to dispense at least 4 gallons of water to eliminate the carbon in the filter plus any air before using it. It’s recommended that this filter be changed every six months or so. The Fridge will chime and alert on the screen. This filter also works for other brands like Maytag, Kenmore, Whirlpool, Amana, Jenn air, etc.

Clean Condenser Coils to Protect Your Refrigerator

 Clogged condenser coils can cause a refrigerator to run warmer or even shorten its lifespan. So, it’s essential to clean your refrigerator’s condenser coils to prevent clogging from dirt, dust, and pet hair. Some models don’t require cleaning, an owner can easily clean some, and others need a certified technician.

**Please consult the use and care guide before attempting to clean the coils. 

If clogged, they cannot efficiently release heat and cause your refrigerator to run warmer or force your compressor to use more energy. Both can shorten the lifespan of your refrigerator. 

How do you clean your condenser Coil on Whirlpool Refrigerator?

Step 1; condenser coils are best cleaned with a vacuum and soft brush. To clean the condenser coils, unplug your refrigerator or disconnect the power. 

Step 2; Remove the base grille at the bottom of the refrigerator. Use a vacuum cleaner and a soft brush to clean the grill, the open areas behind the grille, and the front surface area. 

Step 3; Replace the base grille and plug in the refrigerator or reconnect power. 

Step 4; If the environment is particularly greasy or dusty or there is significant pet traffic, the condenser may require cleaning every two to three months. 

Step 5; It’s best to follow the instructions in the use and care guide or call the customer experience center. 

Find Professional Help!

If you are uncertain about doing it on your own, hire a professional who can work with all safety measures and give you quick results. Irving Refrigerator Service, Texas, has an excellent crew of appliance repair technicians who can make it perfect and 100% guaranteed. Visit the Webpage to know more.

Clean Condenser Coils to Protect Your Refrigerator

Condenser Coils to Protect Your Refrigerator

How do you clean your condenser Coil on Whirlpool Refrigerator?

Clean your condenser Coil on Whirlpool Refrigerator